Viasat+Dreambox-newcamdv5.18 add support for new Viasat card

[tigekala]

Raivo vaata siia, see peaks olema õpetus: http://communication.spectraweb.net/for ... php?t=2580

[sigaelmar]

Paina sinist ja siis kollast nuppu "Cam Reset" ja vahest mitu korda järjest, abistab küll...

[jacobson]

Raivo vaata siia, see peaks olema õpetus: http://communication.spectraweb.net/for ... php?t=2580

See on SKY ITALIA NDS kaardi jaoks.

[i70]

Peale selle peab kontrollima ka faili newcamd.conf

seal on kaks rida lõpu poole:

CWS = dreambox 10000 root dreambox ... lan cardserver
CWS = dreambox 10001 root dreambox ... lan cardserver

10000 on ülemine ja 10001 alumine kaardislot - vaata, et sul selle rea ees, mis kirjeldab slotti, kus on su NDS kaart, ei oleks ees #

Kui on siis korista ära, muidu su kaart tööle ei lähe.

# - see on märkuste rea tähis, st seda rida ei kasutata programmi töös.

[tigekala]

Teid kuulates kaob Dreami isu täiesti, kuigi BSkyB jälle nii ahvatlev...

[i70]

Teid kuulates kaob Dreami isu täiesti, kuigi BSkyB jälle nii ahvatlev...

Näe noormees ei saa kuidagi asjale pihta aga ta on vähemalt väga püüdlik. Ainuke asi, mis mind paneb imestama, on see, et kuidas keegi küll ei viitsi nende emudega kaasas olevaid inglise keelseid jutte lugeda !?

Ja teiseks - kuidas on edusammud BSkyB-ga ? Eestis ei ole just palju originaalkaarte, millelt andmeid sisse lugeda ...

[i70]

Ikka nedest samadest kenadest failikestest loed juttu, kuhu sa neid numbreid topid
Kui peaksid järsku ikkagi mõnda muud keelt peale emakeele oskama, siis siit leiad online translaatori, mis ehk leevendab sinu nõrka inglise keelt

http://dictionary.reference.com/translate/text.html

EDU !

Ja DreamBoxi pole mõtet selles süüdistada kui enesele asi kohale kohe ei jõua

[i70]

SIIT VOL 1 lugemist õhtuks
#
# /var/tuxbox/config/cardserv.cfg
#
# The new cardserver can run several cards at once. It detects cards being
# inserted and removed from configured card readers. Every card uses its
# own TCP port to listen for incoming client connections. Card readers, that
# are configured, but where no card is inserted, will not be initialized.
# Supported are both serial ports of dbox2 (SERIAL_PORT = 0, 1), Dreambox
# cardreaders (SERIAL_PORT = 0 (upper), SERIAL_PORT = 1 (lower)) and the
# Dreambox's serial port (SERIAL_PORT = 2). Supported CA systems are Seca,
# Viaccess, Irdeto, Conax and Cryptoworks. Irdeto cards (or some of them)
# probably won't work in the Dreambox cardreaders, due to driver issues. In
# fact, the only Irdeto cards, that were successfully tested in Dreambox
# cardreaders, are the new Premiere cards and I2 cards. Premiere cards will ONLY
# work with betad (no sharing allowed for Premiere). Betad is a small subset
# of cardserver, using Unix Domain Sockets to communicate with newcamd, also,
# contrary to cardserver, it won't detect card inserts or removals, so Premiere
# card has to be inserted BEFORE betad starts and may never be removed during
# operation of betad. Also betad will only understand a very small subset of
# the options described here. Betad configuration file is called betad.cfg.
#
# You can also start cardserver multiple times by specifying different cfg
# files in the command line. Use only the name of the cfg file, the path of the
# file is always fixed to /var/tuxbox/config (dbox2, Dreambox) or /etc (i386)
#
# Exclude services - Some providers offer a PPV preview by allowing a card
# to decrypt a certain number of ECMs of each PPV event before it has to be
# bought. Sharing such a card with other people allows them to "steal" this
# PPV preview. With this option, you can tell cardserver to not ask the card
# to decrypt ECMs for certain services, except if user 1 (the EMM user) asks
# for them. Each blocked service has to be listed with its service id.
# A service id is a 16-bit number and has to be given in hex.
# camdcmd offers a possibility to change the list of blocked services without
# restarting cardserver (if for example you have bought a PPV event and now
# want to share it).
#
# Boxid (for Viasat-NDS cards only) (L)
# 10-digit serial number of the STB, your Viasat card is married to
# you find this serial number on your original Viasat STB in the following menu:
# Setup->Decoder information->STB Identifier
# take this number and remove the last digit
# take the first (left-most) 10 digits, omit the last (right-most) digit
# BOXID = 0000000000
#
# Block single service
# EXCLUDE_SERVICE = 13a9
# You can also block a range of service ids, the following blocks all services
# from 02be to 02c8
# EXCLUDE_SERVICE_MULTIPLE = 02be:02c8
#
# Example
#
DESKEY = 01 02 03 04 05 06 07 08 09 10 11 12 13 14
SERVER_NAME = cardserv
DEBUG_PORT = 14000
ADMIN_PORT = 14001
ENTITLEMENT_PORT = 14002
ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00
USER = local local lan localhost 12000
USER = cardspider dreambox lan localhost 15003
#
# upper card slot
#
SERIAL_PORT = 0
TCP_PORT = 10000
EMM-G = no
EMM-S = no
EMM-U = no
SPECIAL_FEATURES = no
#
# lower card slot
#
SERIAL_PORT = 1
TCP_PORT = 10001
BOXID = XXXXXXXXXX

[i70]

VOL 2 ÕHTUSEKS LUGEMISEKS

# /var/tuxbox/config/newcamd.conf
#
# newcamd mandatory settings
#
# What Demux API is used? (1 = very old, 2 = rel (Dreambox), 3 = head (VDR))
DEMUX_API = 2
# on PPC version: What Box is used? Valid options are DBOX2, DM7000 and DM5600
# on I386 version this parameter is ignored
BOX_TYPE = DM7000
# Which device for writing control words should be used?
# Valid options are CA, SDEV or GTX
# (SDEV and GTX = /proc/bus/gtx, CA = /dev/caX or /dev/dvb/card0/caX)
CONTROL_WORD_DEVICE = CA
# What CA0 API is used?
# 3 for recent DVB-S driver or recent Dreambox drivers (dream.o from 1.07.3)
# also for ca1 use on dbox2
# 2 for older Dreambox driver (ca.o or dream.o up to 1.07.2)
# no effect on PPC version if CONTROL_WORD_DEVICE = GTX or SDEV
CA_API = 3
# output control words to /proc/bus/gtx in 16 byte or 4096 byte packets
# no effect on I386 version or on PPC version, if BOX_TYPE = DREAMBOX
GTX_OUTPUT_MODE = 16
# This is important for channels which frequently change between free and
# encrypted broadcasts. The change will be reflected in the PMT. If you
# don't want your picture to stop when the channel goes from free access
# mode to encrypted mode, either your zapper (zapit/Enigma) or newcamd
# itself has to keep track of PMT changes. Recent Enigma versions do this,
# so you can set PMT_UPDATE_WATCH to no. Recent Zapit versions also have
# this option, but it is not compiled by default. So when using Zapit
# without PMT updates, you need to enable newcamd to monitor the PMT
# (PMT_UPDATE_WATCH = yes). Having both zapper and newcamd monitor
# the PMT at the same time, can lead to all kind of instabilities and
# should therefore by avoided, even if it seems to work at first.
PMT_UPDATE_WATCH = yes
# Use emulator?
EMU = yes
# if both control word server and emulator keys are available for the
# channel, which method should be tried first?
PREFER_EMU = no
# deactivates the dbox2 Betacrypt CAM
# this has to be set to yes on Dreambox
DISABLE_CAM = yes
# use dbox2 Betacrypt CAM for caids 06, 17 or both (00)?
CAM_CASYS = 17
# Autoupdate for Emu and Control Word Servers
# AU is always yes if there are Betacrypt UDS control word server
# connected to newcamd
AU = yes
#
# newcamd debug options
#
# dumps all ca systems used by a channel on the console
SHOW_ALL_CA_SYSTEMS = no
# On Screen Display, neutrino, enigma or none
OSD = enigma
# Recent Enigma versions come with a new option "Use http authentication"
# in the Expert Setup menu. If this option is enabled, the Enigma web server
# requires all clients to authorize themselves with username (root) and
# password (usually dbox2 or dreambox). The following option tells newcamd
# about the authentication username and password to use for the web server
# in order to be able to display its on screen information.
OSD_WEB_LOGIN = root:dreambox
# print debug messages about ECM handling
DEBUG_ECM = yes
# print debug messages about EMM handling
DEBUG_EMM = yes
# print debug messages about Control Word Server (CWS)
DEBUG_CWS = yes
# print debug messages about dbox2 CAM (cam-alpha.bin)
DEBUG_CAM = yes
# print command message to/from dbox2 CAM as hex strings
DEBUG_CAM_HEX = no
# print all plain control words used
SHOW_CW = no
# hex dump of entire PAT
SHOW_PAT = no
# hex dump of entire PMT
SHOW_PMT = no
# hex dump of entire ECM
SHOW_ECM = no
# hex dump of entire CAT
SHOW_CAT = no
# hex dump of entire EMM (AU)
SHOW_EMM = no
# show network ECM messages being sent and received from/to the cardservers
SHOW_CWS_ECM = yes
# show network EMM messages being sent and received from/to the cardservers
SHOW_CWS_EMM = yes
# hex dump of EMMs with wrong signature
EMM_REPORT_WRONG_SIG = yes
# delay between channel zap and appearance of the OSD
OSD_WAIT_TIME = 3000
#
# newcamd optional settings
#
# Delay between reception of new control word and writing them into
# the CSA registers
# this is a default, can be changed for each individual key in keylist
DEFAULT_CW_DELAY = 500
# reload config on every channel zap
RELOAD_CONFIG_ON_ZAP = yes
# reload keylist on every channel zap
RELOAD_KEYLIST_ON_ZAP = no
# write osd ca info to file
# CA_INFO_FILE = /tmp/cainfo.txt
#
# newcamd mandatory settings for control word servers (cws)
#
# Cardserver list
#
# <hostname> <port> <username> <password> <14 byte triple-des key in hex> <lan/wan> <cardserver name>
#
# wan connections will be dropped and rebuild if newcamd is told so by camdcmd
# (see admin options)
#
# hostname = uds to use betad, port is the serial port in that case
#
#CWS = 127.0.0.1 10000 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserv
CWS = 127.0.0.1 10001 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserv